Prepare Interview

Mock Exams

Make Homepage

Bookmark this page

Subscribe Email Address
Withoutbook LIVE Mock Interviews
The Best LIVE Mock Interview - You should go through before Interview

Freshers / Beginner level questions & answers

Ques 1. How are devices represented in UNIX?

All devices are represented by files called special files that are located in/dev directory.
Thus, device files and other files are named and accessed in the same way. A 'regular file'
is just an ordinary data file in the disk. A 'block special file' represents a device with
characteristics similar to a disk (data transfer in terms of blocks). A 'character special file'
represents a device with characteristics similar to a keyboard (data transfer is by stream of
bits in sequential order).

Is it helpful? Add Comment View Comments
 

Ques 2. What is 'inode'?

All UNIX files have its description stored in a structure called 'inode'. The inode contains
info about the file-size, its location, time of last access, time of last modification,
permission and so on. Directories are also represented as files and have an associated
inode. In addition to descriptions about the file, the inode contains pointers to the data
blocks of the file. If the file is large, inode has indirect pointer to a block of pointers to
additional data blocks (this further aggregates for larger files). A block is typically 8k.
Inode consists of the following fields:
File owner identifier
File type
File access permissions
File access times
Number of links
File size
Location of the file data

Is it helpful? Add Comment View Comments
 

Ques 3. Brief about the directory representation in UNIX

A Unix directory is a file containing a correspondence between filenames and inodes. A directory is a special file that the kernel maintains. Only kernel modifies directories, but processes can read directories. The contents of a directory are a list of filename and inode number pairs. When new directories are created, kernel makes two entries named '.' (refers to the directory itself) and '..' (refers to parent directory).
System call for creating directory is mkdir (pathname, mode).

Is it helpful? Add Comment View Comments
 

Ques 4. What are the Unix system calls for I/O?

open(pathname,flag,mode) - open file
creat(pathname,mode) - create file
close(filedes) - close an open file
read(filedes,buffer,bytes) - read data from an open file
write(filedes,buffer,bytes) - write data to an open file
lseek(filedes,offset,from) - position an open file
dup(filedes) - duplicate an existing file descriptor
dup2(oldfd,newfd) - duplicate to a desired file descriptor
fcntl(filedes,cmd,arg) - change properties of an open file
ioctl(filedes,request,arg) - change the behaviour of an open file
The difference between fcntl anf ioctl is that the former is intended for any open file, while the latter is for device-specific operations.

Is it helpful? Add Comment View Comments
 

Ques 5. What are links and symbolic links in UNIX file system?

A link is a second name (not a file) for a file. Links can be used to assign more than one name to a file, but cannot be used to assign a directory more than one name or link filenames on different computers.
Symbolic link 'is' a file that only contains the name of another file.Operation on the symbolic link is directed to the file pointed by the it.Both the limitations of links are eliminated in symbolic links.
Commands for linking files are:
Link ln filename1 filename2
Symbolic link ln -s filename1 filename2

Is it helpful? Add Comment View Comments
 

Ques 6. What is a FIFO?

FIFO are otherwise called as 'named pipes'. FIFO (first-in-first-out) is a special file which is said to be data transient. Once data is read from named pipe, it cannot be read again. Also, data can be read only in the order written. It is used in interprocess communication where a process writes to one end of the pipe (producer) and the other reads from the other end (consumer).

Is it helpful? Add Comment View Comments
 

Ques 7. How do you create special files like named pipes and device files?

The system call mknod creates special files in the following sequence.
1. kernel assigns new inode,
2. sets the file type to indicate that the file is a pipe, directory or special file,
3. If it is a device file, it makes the other entries like major, minor device numbers.
For example:
If the device is a disk, major device number refers to the disk controller and minor device number is the disk.

Is it helpful? Add Comment View Comments
 

Ques 8. Discuss the mount and unmount system calls

The privileged mount system call is used to attach a file system to a directory of another file system; the unmount system call detaches a file system. When you mount another file system on to your directory, you are essentially splicing one directory tree onto a branch in another directory tree. The first argument to mount call is the mount point, that is , a directory in the current file naming system. The second argument is the file system to mount to that point. When you insert a cdrom to your unix system's drive, the file system in the cdrom automatically mounts to /dev/cdrom in your system.

Is it helpful? Add Comment View Comments
 

Ques 9. How does the inode map to data block of a file?

Inode has 13 block addresses. The first 10 are direct block addresses of the first 10 data blocks in the file. The 11th address points to a one-level index block. The 12th address points to a two-level (double in-direction) index block. The 13th address points to a three-level(triple in-direction)index block. This provides a very large maximum file size with efficient access to large files, but also small files are accessed directly in one disk read.

Is it helpful? Add Comment View Comments
 

Ques 10. What is a shell?</SPAN><SPAN class="answers">
</SPAN>

A shell is an interactive user interface to an operating system services that allows an user to enter commands as character strings or through a graphical user interface. The shell converts them to system calls to the OS or forks off a process to execute the command. System call results and other information from the OS are presented to the user through an interactive interface. Commonly used shells are sh,csh,ks etc.

Is it helpful? Add Comment View Comments
 

Ques 11. Brief about the initial process sequence while the system boots up.

While booting, special process called the 'swapper' or 'scheduler' is created with Process-ID 0. The swapper manages memory allocation for processes and influences CPU allocation. The swapper inturn creates 3 children:
the process dispatcher,
vhand and
dbflush
with IDs 1,2 and 3 respectively.
This is done by executing the file /etc/init. Process dispatcher gives birth to the shell. Unix keeps track of all the processes in an internal data structure called the Process Table (listing command is ps -el).

Is it helpful? Add Comment View Comments
 

Ques 12. What are various IDs associated with a process?

Unix identifies each process with a unique integer called ProcessID. The process that executes the request for creation of a process is called the 'parent process' whose PID is 'Parent Process ID'. Every process is associated with a particular user called the 'owner' who has privileges over the process. The identification for the user is 'UserID'. Owner is the user who executes the process. Process also has 'Effective User ID' which determines the access privileges for accessing resources like files.
getpid() -process id
getppid() -parent process id
getuid() -user id
geteuid() -effective user id

Is it helpful? Add Comment View Comments
 

Ques 13. Explain fork() system call.

The `fork()' used to create a new process from an existing process. The new process is called the child process, and the existing process is called the parent. We can tell which is which by checking the return value from `fork()'. The parent gets the child's pid returned to him, but the child gets 0 returned to him.

Is it helpful? Add Comment View Comments
 

Ques 14. Predict the output of the following program code</P><!--webbot bot="Include" U-Include="../_private/tbl_gglapck.htm" TAG="BODY" startspan --><!--webbot bot="Include" i-checksum="224" endspan --><P class="answers">main()
{
fork();
printf("Hello World!");
}

Hello World!Hello World!
Explanation:
The fork creates a child that is a duplicate of the parent process. The child begins from the fork().All the statements after the call to fork() will be executed twice.(once by the parent process and other by child). The statement before fork() is executed only by the parent process.

Is it helpful? Add Comment View Comments
 

Ques 15. Predict the output of the following program code
main()
{
fork(); fork(); fork();
printf("Hello World!");
}

"Hello World" will be printed 8 times.
Explanation:
2^n times where n is the number of calls to fork()

Is it helpful? Add Comment View Comments
 

Ques 16. List the system calls used for process management:

System calls Description
fork() To create a new process
exec() To execute a new program in a process
wait() To wait until a created process completes its execution
exit() To exit from a process execution
getpid() To get a process identifier of the current process
getppid() To get parent process identifier
nice() To bias the existing priority of a process
brk() To increase/decrease the data segment size of a process

Is it helpful? Add Comment View Comments
 

Ques 17. How can you get/set an environment variable from a program?:

Getting the value of an environment variable is done by using `getenv()'. Setting the value of an environment variable is done by using `putenv()'.

Is it helpful? Add Comment View Comments
 

Ques 18. How can a parent and child process communicate?

A parent and child can communicate through any of the normal inter-process communication schemes (pipes, sockets, message queues, shared memory), but also have some special ways to communicate that take advantage of their relationship as a parent and child. One of the most obvious is that the parent can get the exit status of the child.

Is it helpful? Add Comment View Comments
 

Ques 19. What is a zombie?

When a program forks and the child finishes before the parent, the kernel still keeps some of its information about the child in case the parent might need it - for example, the parent may need to check the child's exit status. To be able to get this information, the parent calls `wait()'; In the interval between the child terminating and the parent calling `wait()', the child is said to be a `zombie' (If you do `ps', the child will have a `Z' in its status field to indicate this.)

Is it helpful? Add Comment View Comments
 

Ques 20. What are the process states in Unix?

As a process executes it changes state according to its circumstances. Unix processes have the following states:
Running : The process is either running or it is ready to run .
Waiting : The process is waiting for an event or for a resource.
Stopped : The process has been stopped, usually by receiving a signal.
Zombie : The process is dead but have not been removed from the process table.

Is it helpful? Add Comment View Comments
 

Ques 21. What Happens when you execute a program?</SPAN><SPAN class="answers">
</SPAN>

When you execute a program on your UNIX system, the system creates a special environment for that program. This environment contains everything needed for the system to run the program as if no other program were running on the system. Each process has process context, which is everything that is unique about the state of the program you are currently running. Every time you execute a program the UNIX system does a fork, which performs a series of operations to create a process context and then execute your program in that context. The steps include the following:
Allocate a slot in the process table, a list of currently running programs kept by UNIX.
Assign a unique process identifier (PID) to the process.
iCopy the context of the parent, the process that requested the spawning of the new process.
Return the new PID to the parent process. This enables the parent process to examine or control the process directly. After the fork is complete, UNIX runs your program.

Is it helpful? Add Comment View Comments
 

Ques 22. What Happens when you execute a command?

When you enter 'ls' command to look at the contents of your current working directory, UNIX does a series of things to create an environment for ls and the run it: The shell has UNIX perform a fork. This creates a new process that the shell will use to run the ls program. The shell has UNIX perform an exec of the ls program. This replaces the shell program and data with the program and data for ls and then starts running that new program. The ls program is loaded into the new process context, replacing the text and data of the shell. The ls program performs its task, listing the contents of the current directory.

Is it helpful? Add Comment View Comments
 

Ques 23. What is a Daemon?

A daemon is a process that detaches itself from the terminal and runs, disconnected, in the background, waiting for requests and responding to them. It can also be defined as the background process that does not belong to a terminal session. Many system functions are commonly performed by daemons, including the sendmail daemon, which handles mail, and the NNTP daemon, which handles USENET news. Many other daemons may exist. Some of the most common daemons are:
init: Takes over the basic running of the system when the kernel has finished the boot process.
inetd: Responsible for starting network services that do not have their own stand-alone daemons. For example, inetd usually takes care of incoming rlogin, telnet, and ftp connections.
cron: Responsible for running repetitive tasks on a regular schedule.

Is it helpful? Add Comment View Comments
 

Ques 24. What is 'ps' command for?

The ps command prints the process status for some or all of the running processes. The information given are the process identification number (PID),the amount of time that the process has taken to execute so far etc.

Is it helpful? Add Comment View Comments
 

Ques 25. How would you kill a process?

The kill command takes the PID as one argument; this identifies which process to terminate. The PID of a process can be got using 'ps' command.

Is it helpful? Add Comment View Comments
 

Ques 26. What is an advantage of executing a process in background?

The most common reason to put a process in the background is to allow you to do something else interactively without waiting for the process to complete. At the end of the command you add the special background symbol, &. This symbol tells your shell to execute the given command in the background.
Example: cp *.* ../backup& (cp is for copy)

Is it helpful? Add Comment View Comments
 

Ques 27. How do you execute one program from within another?

The system calls used for low-level process creation are execlp() and execvp(). The execlp call overlays the existing program with the new one , runs that and exits. The original program gets back control only when an error occurs. execlp(path,file_name,arguments..); //last argument must be NULL A variant of execlp called execvp is used when the number of arguments is not known in advance. execvp(path,argument_array); //argument array should be terminated by NULL

Is it helpful? Add Comment View Comments
 

Ques 28. What is IPC? What are the various schemes available?

The term IPC (Inter-Process Communication) describes various ways by which different process running on some operating system communicate between each other. Various schemes available are as follows: Pipes:
One-way communication scheme through which different process can communicate. The problem is that the two processes should have a common ancestor (parent-child relationship). However this problem was fixed with the introduction of named-pipes (FIFO).
Message Queues :
Message queues can be used between related and unrelated processes running on a machine.
Shared Memory:
This is the fastest of all IPC schemes. The memory to be shared is mapped into the address space of the processes (that are sharing). The speed achieved is attributed to the fact that there is no kernel involvement. But this scheme needs synchronization.
Various forms of synchronisation are mutexes, condition-variables, read-write locks, record-locks, and semaphores.

Is it helpful? Add Comment View Comments
 

Ques 29. What is the difference between Swapping and Paging?

Swapping: Whole process is moved from the swap device to the main memory for execution. Process size must be less than or equal to the available main memory. It is easier to implementation and overhead to the system. Swapping systems does not handle the memory more flexibly as compared to the paging systems.
Paging:
Only the required memory pages are moved to main memory from the swap device for execution. Process size does not matter. Gives the concept of the virtual memory.
It provides greater flexibility in mapping the virtual address space into the physical memory of the machine. Allows more number of processes to fit in the main memory simultaneously. Allows the greater process size than the available physical memory. Demand paging systems handle the memory more flexibly.

Is it helpful? Add Comment View Comments
 

Ques 30. What is major difference between the Historic Unix and the new BSD release of Unix System V in terms of Memory Management?

Historic Unix uses Swapping ? entire process is transferred to the main memory from the swap device, whereas the Unix System V uses Demand Paging ? only the part of the process is moved to the main memory. Historic Unix uses one Swap Device and Unix System V allow multiple Swap Devices.

Is it helpful? Add Comment View Comments
 

Ques 31. What is the main goal of the Memory Management?</SPAN><SPAN class="answers">
</SPAN>

It decides which process should reside in the main memory, Manages the parts of the virtual address space of a process which is non-core resident, Monitors the available main memory and periodically write the processes into the swap device to provide more processes fit in the main memory simultaneously.

Is it helpful? Add Comment View Comments
 

Ques 32. What is a Map?

A Map is an Array, which contains the addresses of the free space in the swap device that are allocatable resources, and the number of the resource units available there.
This allows First-Fit allocation of contiguous blocks of a resource. Initially the Map contains one entry ? address (block offset from the starting of the swap area) and the total number of resources. Kernel treats each unit of Map as a group of disk blocks. On the allocation and freeing of the resources Kernel updates the Map for accurate information.

Is it helpful? Add Comment View Comments
 

Ques 33. What scheme does the Kernel in Unix System V follow while choosing a swap device among the multiple swap devices?

Kernel follows Round Robin scheme choosing a swap device among the multiple swap devices in Unix System V.

Is it helpful? Add Comment View Comments
 

Ques 34. What is a Region?

A Region is a continuous area of a process?s address space (such as text, data and stack). The kernel in a ?Region Table? that is local to the process maintains region. Regions are sharable among the process.

Is it helpful? Add Comment View Comments
 

Ques 35. What are the events done by the Kernel after a process is being swapped out from the main memory?

When Kernel swaps the process out of the primary memory, it performs the following:
Kernel decrements the Reference Count of each region of the process. If the reference count becomes zero, swaps the region out of the main memory,
Kernel allocates the space for the swapping process in the swap device,
Kernel locks the other swapping process while the current swapping operation is going on,
The Kernel saves the swap address of the region in the region table.

Is it helpful? Add Comment View Comments
 

Ques 36. Is the Process before and after the swap are the same? Give reason.

Process before swapping is residing in the primary memory in its original form. The regions (text, data and stack) may not be occupied fully by the process, there may be few empty slots in any of the regions and while swapping Kernel do not bother about the empty slots while swapping the process out. After swapping the process resides in the swap (secondary memory) device. The regions swapped out will be present but only the occupied region slots but not the empty slots that were present before assigning. While swapping the process once again into the main memory, the Kernel referring to the Process Memory Map, it assigns the main memory accordingly taking care of the empty slots in the regions.

Is it helpful? Add Comment View Comments
 

Ques 37. What do you mean by u-area (user area) or u-block?

This contains the private data that is manipulated only by the Kernel. This is local to the Process, i.e. each process is allocated a u-area.

Is it helpful? Add Comment View Comments
 

Ques 38. What are the entities that are swapped out of the main memory while swapping the process out of the main memory?

All memory space occupied by the process, process?s u-area, and Kernel stack are swapped out, theoretically. Practically, if the process?s u-area contains the Address Translation Tables for the process then Kernel implementations do not swap the u-area.

Is it helpful? Add Comment View Comments
 

Ques 39. What is Fork swap?

fork() is a system call to create a child process. When the parent process calls fork() system call, the child process is created and if there is short of memory then the child process is sent to the read-to-run state in the swap device, and return to the user state without swapping the parent process. When the memory will be available the child process will be swapped into the main memory.

Is it helpful? Add Comment View Comments
 

Ques 40. What is Expansion swap?

At the time when any process requires more memory than it is currently allocated, the Kernel performs Expansion swap. To do this Kernel reserves enough space in the swap device. Then the address translation mapping is adjusted for the new virtual address space but the physical memory is not allocated. At last Kernel swaps the process into the assigned space in the swap device. Later when the Kernel swaps the process into the main memory this assigns memory according to the new address translation mapping.

Is it helpful? Add Comment View Comments
 

Ques 41. How the Swapper works?

The swapper is the only process that swaps the processes. The Swapper operates only in the Kernel mode and it does not uses System calls instead it uses internal Kernel functions for swapping. It is the archetype of all kernel process.

Is it helpful? Add Comment View Comments
 

Ques 42. What are the processes that are not bothered by the swapper? Give Reason.</SPAN><SPAN class="answers">
</SPAN>

Zombie process: They do not take any up physical memory.
Processes locked in memories that are updating the region of the process.
Kernel swaps only the sleeping processes rather than the ?ready-to-run? processes, as they have the higher probability of being scheduled than the Sleeping processes.

Is it helpful? Add Comment View Comments
 

Ques 43. What are the requirements for a swapper to work?

The swapper works on the highest scheduling priority. Firstly it will look for any sleeping process, if not found then it will look for the ready-to-run process for swapping. But the major requirement for the swapper to work the ready-to-run process must be core-resident for at least 2 seconds before swapping out. And for swapping in the process must have been resided in the swap device for at least 2 seconds. If the requirement is not satisfied then the swapper will go into the wait state on that event and it is awaken once in a second by the Kernel.

Is it helpful? Add Comment View Comments
 

Ques 44. What are the criteria for choosing a process for swapping into memory from the swap device?

The resident time of the processes in the swap device, the priority of the processes and the amount of time the processes had been swapped out.

Is it helpful? Add Comment View Comments
 

Ques 45. What are the criteria for choosing a process for swapping out of the memory to the swap device?

The process?s memory resident time,
Priority of the process and
The nice value.

Is it helpful? Add Comment View Comments
 

Ques 46. What do you mean by nice value?

Nice value is the value that controls {increments or decrements} the priority of the process. This value that is returned by the nice () system call. The equation for using nice value is: Priority = (?recent CPU usage?/constant) + (base- priority) + (nice value) Only the administrator can supply the nice value. The nice () system call works for the running process only. Nice value of one process cannot affect the nice value of the other process.

Is it helpful? Add Comment View Comments
 

Ques 47. What are conditions on which deadlock can occur while swapping the processes?

</SPAN>
All processes in the main memory are asleep.
All ?ready-to-run? processes are swapped out.
There is no space in the swap device for the new incoming process that are swapped out of the main memory.
There is no space in the main memory for the new incoming process.

Is it helpful? Add Comment View Comments
 

Ques 48. What are conditions for a machine to support Demand Paging?

Memory architecture must based on Pages,
The machine must support the ?restartable? instructions.

Is it helpful? Add Comment View Comments
 

Ques 49. What is ?the principle of locality??

</SPAN>
It?s the nature of the processes that they refer only to the small subset of the total data space of the process. i.e. the process frequently calls the same subroutines or executes the loop instructions.

Is it helpful? Add Comment View Comments
 

Ques 50. What is the working set of a process?

The set of pages that are referred by the process in the last ?n?, references, where ?n? is called the window of the working set of the process.

Is it helpful? Add Comment View Comments
 

Ques 51. What is the window of the working set of a process?

The window of the working set of a process is the total number in which the process had referred the set of pages in the working set of the process.

Is it helpful? Add Comment View Comments
 

Ques 52. What is called a page fault?

Page fault is referred to the situation when the process addresses a page in the working set of the process but the process fails to locate the page in the working set. And on a page fault the kernel updates the working set by reading the page from the secondary device.

Is it helpful? Add Comment View Comments
 

Ques 53. What are data structures that are used for Demand Paging?

Kernel contains 4 data structures for Demand paging. They are,
Page table entries,
Disk block descriptors,
Page frame data table (pfdata),
Swap-use table.

Is it helpful? Add Comment View Comments
 

Ques 54. What are the bits that support the demand paging?</SPAN><SPAN class="answers">
</SPAN>

Valid, Reference, Modify, Copy on write, Age. These bits are the part of the page table entry, which includes physical address of the page and protection bits.
Page address
Age
Copy on write
Modify
Reference
Valid
Protection

Is it helpful? Add Comment View Comments
 

Ques 55. How the Kernel handles the fork() system call in traditional Unix and in the System V Unix, while swapping?

Kernel in traditional Unix, makes the duplicate copy of the parent?s address space and attaches it to the child?s process, while swapping. Kernel in System V Unix, manipulates the region tables, page table, and pfdata table entries, by incrementing the reference count of the region table of shared regions.

Is it helpful? Add Comment View Comments
 

Ques 56. Difference between the fork() and vfork() system call?

During the fork() system call the Kernel makes a copy of the parent process?s address space and attaches it to the child process. But the vfork() system call do not makes any copy of the parent?s address space, so it is faster than the fork() system call. The child process as a result of the vfork() system call executes exec() system call. The child process from vfork() system call executes in the parent?s address space (this can overwrite the parent?s data and stack ) which suspends the parent process until the child process exits.

Is it helpful? Add Comment View Comments
 

Ques 57. What is BSS(Block Started by Symbol)?

A data representation at the machine level, that has initial values when a program starts and tells about how much space the kernel allocates for the un-initialized data. Kernel initializes it to zero at run-time.

Is it helpful? Add Comment View Comments
 

Ques 58. What is Page-Stealer process?

This is the Kernel process that makes rooms for the incoming pages, by swapping the memory pages that are not the part of the working set of a process. Page-Stealer is created by the Kernel at the system initialization and invokes it throughout the lifetime of the system. Kernel locks a region when a process faults on a page in the region, so that page stealer cannot steal the page, which is being faulted in.

Is it helpful? Add Comment View Comments
 

Ques 59. Name two paging states for a page in memory?

The two paging states are:
The page is aging and is not yet eligible for swapping,
The page is eligible for swapping but not yet eligible for reassignment to other virtual address space.

Is it helpful? Add Comment View Comments
 

Ques 60. What are the phases of swapping a page from the memory?

Page stealer finds the page eligible for swapping and places the page number in the list of pages to be swapped. Kernel copies the page to a swap device when necessary and clears the valid bit in the page table entry, decrements the pfdata reference count, and places the pfdata table entry at the end of the free list if its reference count is 0.

Is it helpful? Add Comment View Comments
 

Ques 61. What is page fault? Its types?

Page fault refers to the situation of not having a page in the main memory when any process references it. There are two types of page fault :
Validity fault,
Protection fault.

Is it helpful? Add Comment View Comments
 

Ques 62. In what way the Fault Handlers and the Interrupt handlers are different?

Fault handlers are also an interrupt handler with an exception that the interrupt handlers cannot sleep. Fault handlers sleep in the context of the process that caused the memory fault. The fault refers to the running process and no arbitrary processes are put to sleep.

Is it helpful? Add Comment View Comments
 

Ques 63. What is validity fault?

If a process referring a page in the main memory whose valid bit is not set, it results in validity fault. The valid bit is not set for those pages:
that are outside the virtual address space of a process,
that are the part of the virtual address space of the process but no physical address is assigned to it.

Is it helpful? Add Comment View Comments
 

Ques 64. What does the swapping system do if it identifies the illegal page for swapping?

If the disk block descriptor does not contain any record of the faulted page, then this causes the attempted memory reference is invalid and the kernel sends a ?Segmentation violation? signal to the offending process. This happens when the swapping system identifies any invalid memory reference.

Is it helpful? Add Comment View Comments
 

Ques 65. What are states that the page can be in, after causing a page fault?</SPAN><SPAN class="answers">
</SPAN>

On a swap device and not in memory,
On the free page list in the main memory,
In an executable file,
Marked ?demand zero?,
Marked ?demand fill?.

Is it helpful? Add Comment View Comments
 

Ques 66. In what way the validity fault handler concludes?

It sets the valid bit of the page by clearing the modify bit.
It recalculates the process priority.

Is it helpful? Add Comment View Comments
 

Ques 67. At what mode the fault handler executes?

At the Kernel Mode.

Is it helpful? Add Comment View Comments
 

Ques 68. What do you mean by the protection fault?

Protection fault refers to the process accessing the pages, which do not have the access permission. A process also incur the protection fault when it attempts to write a page whose copy on write bit was set during the fork() system call.

Is it helpful? Add Comment View Comments
 

Ques 69. How the Kernel handles the copy on write bit of a page, when the bit is set?

In situations like, where the copy on write bit of a page is set and that page is shared by more than one process, the Kernel allocates new page and copies the content to the new page and the other processes retain their references to the old page. After copying the Kernel updates the page table entry with the new page number. Then Kernel decrements the reference count of the old pfdata table entry. In cases like, where the copy on write bit is set and no processes are sharing the page, the Kernel allows the physical page to be reused by the processes. By doing so, it clears the copy on write bit and disassociates the page from its disk copy (if one exists), because other process may share the disk copy. Then it removes the pfdata table entry from the page-queue as the new copy of the virtual page is not on the swap device. It decrements the swap-use count for the page and if count drops to 0, frees the swap space.

Is it helpful? Add Comment View Comments
 

Ques 70. For which kind of fault the page is checked first?

The page is first checked for the validity fault, as soon as it is found that the page is invalid (valid bit is clear), the validity fault handler returns immediately, and the process incur the validity page fault. Kernel handles the validity fault and the process will incur the protection fault if any one is present.

Is it helpful? Add Comment View Comments
 

Ques 71. In what way the protection fault handler concludes?

After finishing the execution of the fault handler, it sets the modify and protection bits and clears the copy on write bit. It recalculates the process-priority and checks for signals.

Is it helpful? Add Comment View Comments
 

Ques 72. How the Kernel handles both the page stealer and the fault handler?

The page stealer and the fault handler thrash because of the shortage of the memory. If the sum of the working sets of all processes is greater that the physical memory then the fault handler will usually sleep because it cannot allocate pages for a process. This results in the reduction of the system throughput because Kernel spends too much time in overhead, rearranging the memory in the frantic pace.

Is it helpful? Add Comment View Comments
 

Ques 73. Explain different types of Unix systems.

The most widely used are: 1. System V (AT&T) 2. AIX (IBM) 3. BSD (Berkeley) 4. Solaris (Sun) 5. Xenix ( A PC version of Unix)

Is it helpful? Add Comment View Comments
 

Ques 74. Explain kernal and shell.

Kernal: It carries out basic operating system functions such as allocating memory, accessing files and handling communications. Shell:A shell provides the user interface to the kernal.There are 3 major shells : C-shell, Bourne shell , Korn shell

Is it helpful? Add Comment View Comments
 

Ques 75. What is ex and vi ?

ex is Unix line editor and vi is the standard Unix screen editor.

Is it helpful? Add Comment View Comments
 

Ques 76. Which are typical system directories below the root directory?

(1)/bin: contains many programs which will be executed by users (2)/etc : files used by administrator (3)/dev: hardware devices (4)/lib: system libraries (5)/usr: application software (6)/home: home directories for different systems.

Is it helpful? Add Comment View Comments
 

Ques 77. Construct pipes to execute the following jobs.</SPAN><SPAN class="answers">
</SPAN>

1. Output of who should be displayed on the screen with value of total number of users who have logged in displayed at the bottom of the list.
2. Output of ls should be displayed on the screen and from this output the lines containing the word ?poem? should be counted and the count should be stored in a file.
3. Contents of file1 and file2 should be displayed on the screen and this output should be appended in a file
.
From output of ls the lines containing ?poem? should be displayed on the screen along with the count.
4. Name of cities should be accepted from the keyboard . This list should be combined with the list present in a file. This combined list should be sorted and the sorted list
should be stored in a file ?newcity?.
5. All files present in a directory dir1 should be deleted any error while deleting should be stored in a file ?errorlog?.

Is it helpful? Add Comment View Comments
 

Ques 78. Explain the following commands.

$ ls > file1
$ banner hi-fi > message
$ cat par.3 par.4 par.5 >> report
$ cat file1>file1
$ date ; who
$ date ; who > logfile
$ (date ; who) > logfile

Is it helpful? Add Comment View Comments
 

Ques 79. What is the significance of the ?tee? command?

It reads the standard input and sends it to the standard output while redirecting a copy of what it has read to the file specified by the user.

Is it helpful? Add Comment View Comments
 

Ques 80. What does the command ? $who | sort ?logfile > newfile? do?

The input from a pipe can be combined with the input from a file . The trick is to use the special symbol ?-? (a hyphen) for those commands that recognize the hyphen as std input.
In the above command the output from who becomes the std input to sort , meanwhile sort opens the file logfile, the contents of this file is sorted together with the output of who (rep by the hyphen) and the sorted output is redirected to the file newfile.

Is it helpful? Add Comment View Comments
 

Ques 81. What does the command ?$ls | wc ?l > file1? do?

ls becomes the input to wc which counts the number of lines it receives as input and instead of displaying this count , the value is stored in file1.

Is it helpful? Add Comment View Comments
 

Ques 82. Which of the following commands is not a filter man , (b) cat , (c) pg , (d) head

man A filter is a program which can receive a flow of data from std input, process (or filter) it and send the result to the std output.

Is it helpful? Add Comment View Comments
 

Ques 83. How is the command ?$cat file2 ? different from ?$cat >file2 and >> redirection operators ?

is the output redirection operator when used it overwrites while >> operator appends into the file.

Is it helpful? Add Comment View Comments
 

Ques 84. Explain the steps that a shell follows while processing a command.

After the command line is terminated by the key, the shell goes ahead with processing the command line in one or more passes. The sequence is well defined and assumes the following order.
Parsing: The shell first breaks up the command line into words, using spaces and the delimiters, unless quoted. All consecutive occurrences of a space or tab are replaced here with a single space.
Variable evaluation: All words preceded by a $ are valuated as variables, unless quoted or escaped.
Command substitution: Any command surrounded by back quotes is executed by the shell which then replaces the standard output of the command into the command line.
Wild-card interpretation: The shell finally scans the command line for wild-cards (the characters *, ?, [, ]).
Any word containing a wild-card is replaced by a sorted list of
filenames that match the pattern. The list of these filenames then forms the arguments to the command.
PATH evaluation: It finally looks for the PATH variable to determine the sequence of directories it has to search in order to hunt for the command.

Is it helpful? Add Comment View Comments
 

Ques 85. What difference between cmp and diff commands?

cmp - Compares two files byte by byte and displays the first mismatch diff - tells the changes to be made to make the files identical

Is it helpful? Add Comment View Comments
 

Ques 86. What is the use of ?grep? command?</SPAN><SPAN class="answers">
</SPAN>

?grep? is a pattern search command. It searches for the pattern, specified in the command line with appropriate option, in a file(s).
Syntax : grep
Example : grep 99mx mcafile

Is it helpful? Add Comment View Comments
 

Ques 87. What is the difference between cat and more command?

Cat displays file contents. If the file is large the contents scroll off the screen before we view it. So command 'more' is like a pager which displays the contents page by page.

Is it helpful? Add Comment View Comments
 

Ques 88. Write a command to kill the last background job?

Kill $!

Is it helpful? Add Comment View Comments
 

Ques 89. Which command is used to delete all files in the current directory and all its sub-directories?

rm -r *

Is it helpful? Add Comment View Comments
 

Ques 90. Write a command to display a file?s contents in various formats?

$od -cbd file_name
c - character, b - binary (octal), d-decimal, od=Octal Dump.

Is it helpful? Add Comment View Comments
 

Ques 91. What will the following command do?

$ echo *
It is similar to 'ls' command and displays all the files in the current directory.

Is it helpful? Add Comment View Comments
 

Ques 92. Is it possible to create new a file system in UNIX?

Yes, 'mkfs' is used to create a new file system.

Is it helpful? Add Comment View Comments
 

Ques 93. Is it possible to restrict incoming message?

Yes, using the 'mesg' command.

Is it helpful? Add Comment View Comments
 

Ques 94. What is the use of the command "ls -x chapter[1-5]"

ls stands for list; so it displays the list of the files that starts with 'chapter' with suffix '1' to '5', chapter1, chapter2, and so on.

Is it helpful? Add Comment View Comments
 

Ques 95. Is 'du' a command? If so, what is its use?

Yes, it stands for 'disk usage'. With the help of this command you can find the disk capacity and free space of the disk.

Is it helpful? Add Comment View Comments
 

Ques 96. Is it possible to count number char, line in a file; if so, How?

Yes, wc-stands for word count.
wc -c for counting number of characters in a file.
wc -l for counting lines in a file.

Is it helpful? Add Comment View Comments
 

Ques 97. Name the data structure used to maintain file identification?

'inode', each file has a separate inode and a unique inode number.

Is it helpful? Add Comment View Comments
 

Ques 98. How many prompts are available in a UNIX system?

Two prompts, PS1 (Primary Prompt), PS2 (Secondary Prompt).

Is it helpful? Add Comment View Comments
 

Ques 99. How does the kernel differentiate device files and ordinary files?

Kernel checks 'type' field in the file's inode structure.

Is it helpful? Add Comment View Comments
 

Ques 100. How to switch to a super user status to gain privileges?

Use 'su' command. The system asks for password and when valid entry is made the user gains super user (admin) privileges.

Is it helpful? Add Comment View Comments
 

Ques 101. What are shell variables?

Shell variables are special variables, a name-value pair created and maintained by the shell.
Example: PATH, HOME, MAIL and TERM

Is it helpful? Add Comment View Comments
 

Ques 102. What is redirection?

</SPAN>
Directing the flow of data to the file or from the file for input or output.
Example : ls > wc

Is it helpful? Add Comment View Comments
 

Ques 103. How to terminate a process which is running and the specialty on command kill 0?

With the help of kill command we can terminate the process.
Syntax: kill pid
Kill 0 - kills all processes in your system except the login shell.

Is it helpful? Add Comment View Comments
 

Ques 104. What is a pipe and give an example?

A pipe is two or more commands separated by pipe char '|'. That tells the shell to arrange for the output of the preceding command to be passed as input to the following command.
Example : ls -l | pr
The output for a command ls is the standard input of pr.
When a sequence of commands are combined using pipe, then it is called pipeline.

Is it helpful? Add Comment View Comments
 

Ques 105. Explain kill() and its possible return values.

There are four possible results from this call:
'kill()' returns 0. This implies that a process exists with the given PID, and the system would allow you to send signals to it. It is system-dependent whether the process could be a zombie.
?kill()? returns -1, ?errno == ESRCH? either no process exists with the given PID, or security enhancements are causing the system to deny its existence. (On some systems, the process could be a zombie.)
?kill()? returns -1, ?errno == EPERM? the system would not allow you to kill the specified process. This means that either the process exists (again, it could be a zombie) or draconian security enhancements are present (e.g. your process is not allowed to send signals to *anybody*).
?kill()? returns -1, with some other value of ?errno? you are in trouble! The most-used technique is to assume that success or failure with ?EPERM? implies that the process exists, and any other error implies that it doesn't.
An alternative exists, if you are writing specifically for a system (or all those systems) that provide a ?/proc? filesystem: checking for the existence of '/proc/PID' may work.

Is it helpful? Add Comment View Comments
 

Most helpful rated by users:

Related differences

Linux vs Unix

Related interview subjects

Unix interview questions and answers - Total 105 questions
Weblogic interview questions and answers - Total 30 questions
Tomcat interview questions and answers - Total 16 questions
Glassfish interview questions and answers - Total 8 questions
Ubuntu interview questions and answers - Total 30 questions
Linux interview questions and answers - Total 43 questions

All interview subjects

ASP interview questions and answers - Total 82 questions
LINQ interview questions and answers - Total 20 questions
C# interview questions and answers - Total 41 questions
ASP .NET interview questions and answers - Total 31 questions
Microsoft .NET interview questions and answers - Total 60 questions
TensorFlow interview questions and answers - Total 30 questions
Hugging Face interview questions and answers - Total 30 questions
Artificial Intelligence (AI) interview questions and answers - Total 47 questions
Machine Learning interview questions and answers - Total 30 questions
Google Cloud AI interview questions and answers - Total 30 questions
IBM Watson interview questions and answers - Total 30 questions
ChatGPT interview questions and answers - Total 20 questions
NLP interview questions and answers - Total 30 questions
OpenCV interview questions and answers - Total 36 questions
Amazon SageMaker interview questions and answers - Total 30 questions
C++ interview questions and answers - Total 142 questions
VBA interview questions and answers - Total 30 questions
COBOL interview questions and answers - Total 50 questions
R Language interview questions and answers - Total 30 questions
Python Coding interview questions and answers - Total 20 questions
Scala interview questions and answers - Total 48 questions
Swift interview questions and answers - Total 49 questions
Golang interview questions and answers - Total 30 questions
Embedded C interview questions and answers - Total 30 questions
CCNA interview questions and answers - Total 40 questions
OpenStack interview questions and answers - Total 30 questions
ServiceNow interview questions and answers - Total 30 questions
Snowflake interview questions and answers - Total 30 questions
Oracle APEX interview questions and answers - Total 23 questions
AWS interview questions and answers - Total 87 questions
Microsoft Azure interview questions and answers - Total 35 questions
Azure Data Factory interview questions and answers - Total 30 questions
DPDP interview questions and answers - Total 30 questions
PIPEDA interview questions and answers - Total 20 questions
GDPR interview questions and answers - Total 30 questions
CCPA interview questions and answers - Total 20 questions
HITRUST interview questions and answers - Total 20 questions
LGPD interview questions and answers - Total 20 questions
PDPA interview questions and answers - Total 20 questions
OSHA interview questions and answers - Total 20 questions
HIPPA interview questions and answers - Total 20 questions
PHIPA interview questions and answers - Total 20 questions
FERPA interview questions and answers - Total 20 questions
Operating System interview questions and answers - Total 22 questions
MS Word interview questions and answers - Total 50 questions
Tips and Tricks interview questions and answers - Total 30 questions
PoowerPoint interview questions and answers - Total 50 questions
Data Structures interview questions and answers - Total 49 questions
Computer Networking interview questions and answers - Total 65 questions
Microsoft Excel interview questions and answers - Total 37 questions
Computer Basics interview questions and answers - Total 62 questions
Computer Science interview questions and answers - Total 50 questions
NumPy interview questions and answers - Total 30 questions
Python interview questions and answers - Total 106 questions
Python Pandas interview questions and answers - Total 48 questions
Django interview questions and answers - Total 50 questions
Python Matplotlib interview questions and answers - Total 30 questions
Pandas interview questions and answers - Total 30 questions
Deep Learning interview questions and answers - Total 29 questions
Flask interview questions and answers - Total 40 questions
PySpark interview questions and answers - Total 30 questions
PyTorch interview questions and answers - Total 25 questions
Data Science interview questions and answers - Total 23 questions
SciPy interview questions and answers - Total 30 questions
Generative AI interview questions and answers - Total 30 questions
IBM DB2 interview questions and answers - Total 40 questions
Elasticsearch interview questions and answers - Total 61 questions
Data Mining interview questions and answers - Total 30 questions
Oracle interview questions and answers - Total 34 questions
MongoDB interview questions and answers - Total 27 questions
AWS DynamoDB interview questions and answers - Total 46 questions
Entity Framework interview questions and answers - Total 46 questions
Redis Cache interview questions and answers - Total 20 questions
MySQL interview questions and answers - Total 108 questions
Data Modeling interview questions and answers - Total 30 questions
MariaDB interview questions and answers - Total 40 questions
DBMS interview questions and answers - Total 73 questions
Apache Hive interview questions and answers - Total 30 questions
PostgreSQL interview questions and answers - Total 30 questions
SSIS interview questions and answers - Total 30 questions
Teradata interview questions and answers - Total 20 questions
SQL Query interview questions and answers - Total 70 questions
SQLite interview questions and answers - Total 53 questions
Cassandra interview questions and answers - Total 25 questions
Neo4j interview questions and answers - Total 44 questions
MSSQL interview questions and answers - Total 50 questions
OrientDB interview questions and answers - Total 46 questions
Data Warehouse interview questions and answers - Total 20 questions
SQL interview questions and answers - Total 152 questions
Verilog interview questions and answers - Total 30 questions
VLSI interview questions and answers - Total 30 questions
Software Engineering interview questions and answers - Total 27 questions
MATLAB interview questions and answers - Total 25 questions
Digital Electronics interview questions and answers - Total 38 questions
Civil Engineering interview questions and answers - Total 30 questions
Electrical Machines interview questions and answers - Total 29 questions
Data Engineer interview questions and answers - Total 30 questions
AutoCAD interview questions and answers - Total 30 questions
Robotics interview questions and answers - Total 28 questions
Power System interview questions and answers - Total 28 questions
Electrical Engineering interview questions and answers - Total 30 questions
IBM DataStage interview questions and answers - Total 20 questions
Talend interview questions and answers - Total 34 questions
Salesforce interview questions and answers - Total 57 questions
TIBCO interview questions and answers - Total 30 questions
Informatica interview questions and answers - Total 48 questions
Oracle CXUnity interview questions and answers - Total 29 questions
Web Services interview questions and answers - Total 10 questions
Salesforce Lightning interview questions and answers - Total 30 questions
IBM Integration Bus interview questions and answers - Total 30 questions
Power BI interview questions and answers - Total 24 questions
OIC interview questions and answers - Total 30 questions
Dell Boomi interview questions and answers - Total 30 questions
Web API interview questions and answers - Total 31 questions
Java 8 interview questions and answers - Total 30 questions
Hibernate interview questions and answers - Total 52 questions
JMS interview questions and answers - Total 64 questions
JSF interview questions and answers - Total 24 questions
Java 17 interview questions and answers - Total 20 questions
Spring Boot interview questions and answers - Total 50 questions
Servlets interview questions and answers - Total 34 questions
Kotlin interview questions and answers - Total 30 questions
EJB interview questions and answers - Total 80 questions
Java Beans interview questions and answers - Total 57 questions
Java Exception Handling interview questions and answers - Total 30 questions
Java 15 interview questions and answers - Total 16 questions
Apache Wicket interview questions and answers - Total 26 questions
Core Java interview questions and answers - Total 306 questions
Java Multithreading interview questions and answers - Total 30 questions
Log4j interview questions and answers - Total 35 questions
JBoss interview questions and answers - Total 14 questions
Java Mail interview questions and answers - Total 27 questions
Java Applet interview questions and answers - Total 29 questions
Java 21 interview questions and answers - Total 21 questions
Google Gson interview questions and answers - Total 8 questions
Apache Camel interview questions and answers - Total 20 questions
Struts interview questions and answers - Total 84 questions
RMI interview questions and answers - Total 31 questions
Java Support interview questions and answers - Total 30 questions
JAXB interview questions and answers - Total 18 questions
Apache Tapestry interview questions and answers - Total 9 questions
JSP interview questions and answers - Total 49 questions
Java Concurrency interview questions and answers - Total 30 questions
J2EE interview questions and answers - Total 25 questions
JUnit interview questions and answers - Total 24 questions
Java OOPs interview questions and answers - Total 30 questions
Java 11 interview questions and answers - Total 24 questions
JDBC interview questions and answers - Total 27 questions
Java Garbage Collection interview questions and answers - Total 30 questions
Spring Framework interview questions and answers - Total 53 questions
Java Swing interview questions and answers - Total 27 questions
Java Design Patterns interview questions and answers - Total 15 questions
JPA interview questions and answers - Total 41 questions
SCCM interview questions and answers - Total 30 questions
Tally interview questions and answers - Total 30 questions
Pega interview questions and answers - Total 30 questions
ITIL interview questions and answers - Total 25 questions
Finance interview questions and answers - Total 30 questions
JIRA interview questions and answers - Total 30 questions
SAP MM interview questions and answers - Total 30 questions
SAP ABAP interview questions and answers - Total 24 questions
Mobile Computing interview questions and answers - Total 20 questions
Xamarin interview questions and answers - Total 31 questions
iOS interview questions and answers - Total 52 questions
Ionic interview questions and answers - Total 32 questions
Android interview questions and answers - Total 14 questions
Sales interview questions and answers - Total 30 questions
Nature interview questions and answers - Total 20 questions
Chemistry interview questions and answers - Total 50 questions
Docker interview questions and answers - Total 30 questions
Cryptography interview questions and answers - Total 40 questions
RPA interview questions and answers - Total 26 questions
Interview Tips interview questions and answers - Total 30 questions
College Teachers interview questions and answers - Total 30 questions
SDLC interview questions and answers - Total 75 questions
Blue Prism interview questions and answers - Total 20 questions
Memcached interview questions and answers - Total 28 questions
GIT interview questions and answers - Total 30 questions
Algorithm interview questions and answers - Total 50 questions
Business Analyst interview questions and answers - Total 40 questions
Splunk interview questions and answers - Total 30 questions
DevOps interview questions and answers - Total 45 questions
Accounting interview questions and answers - Total 30 questions
SSB interview questions and answers - Total 30 questions
OSPF interview questions and answers - Total 30 questions
Sqoop interview questions and answers - Total 30 questions
JSON interview questions and answers - Total 16 questions
Accounts Payable interview questions and answers - Total 30 questions
Computer Graphics interview questions and answers - Total 25 questions
IoT interview questions and answers - Total 30 questions
Insurance interview questions and answers - Total 30 questions
Scrum Master interview questions and answers - Total 30 questions
Laravel interview questions and answers - Total 30 questions
XML interview questions and answers - Total 25 questions
GraphQL interview questions and answers - Total 32 questions
Bitcoin interview questions and answers - Total 30 questions
Active Directory interview questions and answers - Total 30 questions
Microservices interview questions and answers - Total 30 questions
Apache Kafka interview questions and answers - Total 38 questions
Tableau interview questions and answers - Total 20 questions
Adobe AEM interview questions and answers - Total 50 questions
Kubernetes interview questions and answers - Total 30 questions
OOPs interview questions and answers - Total 30 questions
Fashion Designer interview questions and answers - Total 20 questions
Desktop Support interview questions and answers - Total 30 questions
IAS interview questions and answers - Total 56 questions
PHP OOPs interview questions and answers - Total 30 questions
Nursing interview questions and answers - Total 40 questions
Linked List interview questions and answers - Total 15 questions
Dynamic Programming interview questions and answers - Total 30 questions
SharePoint interview questions and answers - Total 28 questions
CICS interview questions and answers - Total 30 questions
Yoga Teachers Training interview questions and answers - Total 30 questions
Language in C interview questions and answers - Total 80 questions
Behavioral interview questions and answers - Total 29 questions
School Teachers interview questions and answers - Total 25 questions
Statistics interview questions and answers - Total 30 questions
Digital Marketing interview questions and answers - Total 40 questions
Apache Spark interview questions and answers - Total 24 questions
Full-Stack Developer interview questions and answers - Total 60 questions
VISA interview questions and answers - Total 30 questions
IIS interview questions and answers - Total 30 questions
System Design interview questions and answers - Total 30 questions
SEO interview questions and answers - Total 51 questions
Google Analytics interview questions and answers - Total 30 questions
Cloud Computing interview questions and answers - Total 42 questions
BPO interview questions and answers - Total 48 questions
ANT interview questions and answers - Total 10 questions
HR Questions interview questions and answers - Total 49 questions
REST API interview questions and answers - Total 52 questions
Content Writer interview questions and answers - Total 30 questions
SAS interview questions and answers - Total 24 questions
Control System interview questions and answers - Total 28 questions
Agile Methodology interview questions and answers - Total 30 questions
Mainframe interview questions and answers - Total 20 questions
Hadoop interview questions and answers - Total 40 questions
Banking interview questions and answers - Total 20 questions
Checkpoint interview questions and answers - Total 20 questions
Blockchain interview questions and answers - Total 29 questions
Technical Support interview questions and answers - Total 30 questions
Next.js interview questions and answers - Total 30 questions
Knockout JS interview questions and answers - Total 25 questions
TypeScript interview questions and answers - Total 38 questions
PowerShell interview questions and answers - Total 27 questions
Terraform interview questions and answers - Total 30 questions
JCL interview questions and answers - Total 20 questions
JavaScript interview questions and answers - Total 59 questions
Ajax interview questions and answers - Total 58 questions
Express.js interview questions and answers - Total 30 questions
Ansible interview questions and answers - Total 30 questions
ES6 interview questions and answers - Total 30 questions
Electron.js interview questions and answers - Total 24 questions
RxJS interview questions and answers - Total 29 questions
NodeJS interview questions and answers - Total 30 questions
ExtJS interview questions and answers - Total 50 questions
jQuery interview questions and answers - Total 22 questions
Vue.js interview questions and answers - Total 30 questions
Svelte.js interview questions and answers - Total 30 questions
Shell Scripting interview questions and answers - Total 50 questions
Data Protection Act interview questions and answers - Total 20 questions
BGP interview questions and answers - Total 30 questions
Ethical Hacking interview questions and answers - Total 40 questions
Cyber Security interview questions and answers - Total 50 questions
PII interview questions and answers - Total 30 questions
Unix interview questions and answers - Total 105 questions
Weblogic interview questions and answers - Total 30 questions
Tomcat interview questions and answers - Total 16 questions
Glassfish interview questions and answers - Total 8 questions
Ubuntu interview questions and answers - Total 30 questions
Linux interview questions and answers - Total 43 questions
ETL Testing interview questions and answers - Total 20 questions
QTP interview questions and answers - Total 44 questions
Cucumber interview questions and answers - Total 30 questions
Postman interview questions and answers - Total 30 questions
TestNG interview questions and answers - Total 38 questions
SDET interview questions and answers - Total 30 questions
Selenium interview questions and answers - Total 40 questions
Kali Linux interview questions and answers - Total 29 questions
Mobile Testing interview questions and answers - Total 30 questions
UiPath interview questions and answers - Total 38 questions
Quality Assurance interview questions and answers - Total 56 questions
API Testing interview questions and answers - Total 30 questions
Appium interview questions and answers - Total 30 questions
Dojo interview questions and answers - Total 23 questions
Symfony interview questions and answers - Total 30 questions
GWT interview questions and answers - Total 27 questions
CSS interview questions and answers - Total 74 questions
Ruby On Rails interview questions and answers - Total 74 questions
Yii interview questions and answers - Total 30 questions
Angular interview questions and answers - Total 50 questions
PHP interview questions and answers - Total 27 questions
Oracle JET(OJET) interview questions and answers - Total 54 questions
Frontend Developer interview questions and answers - Total 30 questions
Zend Framework interview questions and answers - Total 24 questions
RichFaces interview questions and answers - Total 26 questions
HTML interview questions and answers - Total 27 questions
Flutter interview questions and answers - Total 25 questions
CakePHP interview questions and answers - Total 30 questions
React interview questions and answers - Total 40 questions
React Native interview questions and answers - Total 26 questions
Web Developer interview questions and answers - Total 50 questions
Angular 8 interview questions and answers - Total 32 questions
Angular JS interview questions and answers - Total 21 questions
©2024 WithoutBook